| FIELD INSTALLED PUSH-LOCK™ FITTINGS MAKE CABLE RAILING EASY TO INSTALL |
Two styles make your job easy – in metal or wood |
| NO FIELD SWAGING! |
Push-Lock™ fittings with rounded cap ends rest inside your metal or wood end posts on level runs. The fitting is hidden inside the post, with only the head exposed on the outside of the post. |
| **These fittings are stationary. They must be used with a tensioner on the opposite end.** |
| Note: For 1/2" cable and straight pull applications only. |
 |
| Push-Lock™ fittings with threaded eyes mount to lag eyes, tabs or holes on the outside of your metal or wood post for use on stairs and severe pitches.
|
|
|
Cables come with a tensioner on one end. Install the tensioner on one end post, then cut the cable to length. Slip the Push-Lock™ fitting into the other end post or mount it with the tab to the outside of the post.
Push the cable into the Push-Lock™ fitting, tension the cable and you’re done.
Note: Push-Lock™ Tool Kit is required
|
EASY TO ORDER – EASY TO INSTALL
Select the tensioners you wish to use and provide the length of each of your cable runs. The cables will be shipped with tensioners swaged on one end and bare cable on the other end. Pre-cut cable will be approximately 3" longer than required to allow for potential fraying. Cut each cable to a final length on site and push it into the opening in the Push-Lock™ fitting. |
|
|
|
|
| PUSH-LOCK™ FOR LEVEL RUNS |
|
| Type 316 Stainless Steel |
|
| These Push-Lock™ fittings with rounded ends are used on level runs. They rest in a hole in the end post. When used with an end post 1-1/2" or more in thickness, the Push-Lock™ fitting is hidden inside the end post with only the head exposed on the outside of the post. Pipe ends are counterbored so the full perimeter of the head will rest on a flat surface in the pipe. A Plastic Washer is included and acts as a scratch-resistant barrier between the Push-Lock™ fitting and a metal post. The head rests on the outside wall of a flat-sided metal post or on a stainless steel washer on a wooden post. For wood applications, also order part number CR716SAE Washer. |
 |
 |
|
Cable Size
|
Frame Options
|
Stainless Steel
|
For Wood Post Use Washer #
|
|
1/8"
|
1.500" Tube
|
CRPL4M
|
CR716SAE
|
|
1/8"
|
1-1/4" Pipe
|
CRPL4M
|
CR716SAE
|
|
1/8"
|
Other Frames
|
CRPl4
|
CR716SAE
|
|
|
| PUSH-LOCK™ FOR STAIRS OR SEVERE PITCHES |
|
| Type 316 Stainless Steel |
|
| These fittings have a 1/4-28 threaded eye end and are for use on stairs. They attach to a wood end post with a CRLE6 shown on page 55. For metal posts, use a Fixed Tab or Threaded Tab. Mount with a CRSC6 Screw. |
| |
|
Cable Size
|
Stainless Steel
|
Use with Screw # (included)
|
For Wood Post Use Lag Eye #
|
For Stainless Post Use Fixed Tab #
|
For Stainless Post Use Threaded Tab #
|
For Steel Post Use Threaded Tab #
|
|
1/8"
|
CRPLTE4
|
CRSC6
|
CRLE6
|
CRFT65B
|
CRTT6B
|
CRFT65A
|
|
|
 |
|
| *Click here to download our spec sheet on this product. |
|
| FIELD INSTALLED PUSH-LOCKS™ STUDS REQUIRE NO SWAGING OR SPECIAL TOOLS |
USE WITH METAL OR WOOD POSTS
The receiver with Push-Lock™ stud rests inside your metal or wood end post |
| NO FIELD SWAGING |
| For use in wood, the fitting can rest against the outside of the end post or the post can be counterbored with the fitting recessed in the post. For wood applications, a larger diameter washer is needed to distribute the load over a wider surface. See CR716SAE Stainless Steel Washer. |
 |
|
| Similar to our Invisiware® receivers but when used with Push-Lock™ studs there is no need to swage the threaded stud onto the cable. Receivers with Push-Lock™ swageless studs can be used with any fitting on the other end but when used with our other swageless fittings, both ends can be put on the cable by hand without any swaging or special tools. |
| EASY TO INSTALL |
| Push-Lock™ studs are designed for use with 1 × 19 L.H. lay strand only. Push the cable into the Push-Lock™ swageless stud, where it will be securely held inside the fitting. The receiver is female-threaded to accept the male-threaded end of the fitting. The head of the receiver is broached for an Allen wrench. To tension the cable, use an Allen wrench to rotate the receiver around the threaded end of the stud. |
 |
 |
| CABLE RELEASE |
| Releases cable from Push-Lock™ and Pull-Lock™ type fittings before cables are tensioned. |
| Cable Release |
CRPKLEY |
|
|
|
|
Cable Size
|
Use with Swageless Stud #
|
A= Length of Receiver Body
|
Receiver
|
|
1/8"
|
CRPLST4
|
1.562"
|
CRR612
|
|
1/8"
|
CRPLST4
|
1.812"
|
CRR622
|
|
1/8"
|
CRPLST4
|
2.030"
|
CRR632
|
|
1/8"
|
CRPLST4
|
2.301"
|
CRR642
|
|
1/8"
|
CRPLST4
|
2.375"
|
CRR672
|
|
1/8"
|
CRPLST4
|
3.03"
|
CRR652
|
|
1/8"
|
CRPLST4
|
3.562"
|
CRR662
|
| USE PUSH-LOCK™ FITTINGS ON STAIRS OR SEVERE PITCHES WITH SPECIAL BEVELED WASHERS. |
|
Special stainless steel beveled washers let you use Push-Lock™ tensioners on stairs or severe pitches with flat-sided metal posts. (Not offered for pipe or round tubing.)
With wood posts, you need to counterbore a 1" diameter hole at an angle, to accept the over-sized stainless steel washer that distributes the load over a wider surface than is required with a metal post.
|
|
Pitch/Angle
|
1/8" Cable
|
|
30°-33°
|
CRBW326
|
|
34°-36°
|
CRBW356
|
|
37°-39°
|
CRBW386
|
|
|
PUSH |
LOCK |
|
|
PUSH-LOCK™ SWAGELESS STUD
The Push-Lock™ swageless stud is installed onto the end of the cable by hand, by pushing the cable into the fitting where it is held securely inside. No swaging is required, and other than a cable cutter, no special tools are needed.
 |
|
Cable Size
|
Stainless Steel
|
|
1/8"
|
CRPLST4
|
|
|
|
|