|
|
|
Photo Showcase
Jeff Whipkey of SDC Products
17030 West Little York
Houston, TX 77084
281-859-9339
www.sdcproducts.com
sent this article and photos.
We started this project like any other, once the job was ready we built a template on-site using 1/2" x 16ga steel tubing, then we constructed a faux staircase in our shop to start the work. We used low carbon steel for the entire railing. Balusters were made of 1/2" round bar that were textured with our air hammer, top and bottom rails were 1-1/4" x 3/8" flat bar, newel posts were 1-1/4" round bar also textured with the air hammer. We new this work would look very busy with the design so we opted to put the balusters on 6" centers.
|
|
|
|
Each newel post represents a single grape trunk, so we added 1/4, 3/8 and 1/2" round bar to the base area to show the beginnings of the root system and used a die grinder to blend them in. This root system also gave us the platform to mount the railing and help hide the anchor screws. After the main railing system was welded together we wove the vines through the balusters, beginning at the trunks and toward each other trunk. Weaving was random but we kept the building code in mind so it would pass the 4" rule and we used the leaves and grape clusters to help manage this. We also have twists and knots through out the vine system just like the real ones.
|
Once the railing was complete we sand blasted it. Next we used red oxide primer followed by a flat black enamel base to enhance the colors we were going to apply. Gilders Paste™ was used to add the colors we wanted because of its richness and durability. No thinning was required, and it was applied using a soft cloth and fingertips. No clear coat was needed thanks to the hard finish of the paste and we wanted to keep that "natural look".
|
 |
This project had 55 ft of railing. We used 600 leaves of various sizes, 35 grape clusters and hundreds of feet of vines. We used four different colors of paste for the detailing and never used all of either color. That past goes a long way! FYI all the color detailing was applied on site and after all other trades were finished and gone. An interior trim carpenter applied the wood rail cap.
Foundry Bronze was used for the trunks and vines, African Bronze for the leaves, Pinotage and German Silver for the grape clusters. We had around 400 man hours in this project from start to finish.
|
Rubbed Black with toothbrush as a base, Verdigris applied with finger on the leave stems and leaves, African Bronze was applied with finger on top of Verdigris on the leaves and Tulip Red on the roses.
Finally, the piece was Powder coated with a clear polyester.
ACME Powder Coating, Elk Grove, IL.
|
|
|
|
|
The grapes have been rubbed with Iris Blue and German Silver on top. The leaves have African Bronze and the bottle has Gold, Iris Blue and German Silver. The grape vine has diluted Bronze painted and rubbed off to create a stained effect. Antique Gold was brushed over the stain with a 2" soft trim brush.
Grainger Metal Works, Conway, SC.
|
|
|
Peter’s Metal Studio,
Johannesburg, South Africa
|
|
|
|
The iron casting was sand blasted with fine silica sand and wiped down with mineral spirits to remove rust, scale, dirt and dust. The base coat on the
leaves and stems is Verdigris, lightly extended with mineral spirits to stain the casting green using a toothbrush. African Bronze was applied over the
Verdigris after 10 minutes with finger, following the direction of the leaves raised portions. The flowers were covered with Cream using a toothbrush and
Canary Yellow applied with finger on a small portion of the petals. Tulip Red was applied with a stencil brush to simulate stamens. After 12 hours to allow full drying time, the piece was wiped down with a soft cloth to produce a shiny to gloss appearance.
 |
|
|
|